Dixon ZTR 6601 Betreibershandbuch

DIXON LIMITED WARRANTY POLICY -- HYDRO-GEAR MODELS This warranty policy applies to all HydroGear mowers or any 50" model, purchased on or after M

SPECIFICATIONS Model ZTR 6601 CHASSIS: 11 GA - rectangular tube BODY: Two piece - made of rotational molded polyethylene. Front body contains acce

SEAT ADJUSTMENT INSTRUCTIONS 1. Place parking brake in ON position. (Pull brake lever up) 2. Raise and push seat assembly and upper body rea

CONTROLS Page 10

CONTROLS PARKING BRAKE: The parking brake used on the Model ZTR 6601 is designed to hold the mower from moving and is not intended for use in stopping

TO GO FORWARD: From neutral position, gently push both drive levers forward. To increase speed, move levers farther forward. TO GO BACKWARD: From neut

CONTROLS BLADE DRIVE: Located on control panel, on operator's right. To engage the mower blades, lift switch up lightly and push forward. To dise

OPERATION INSTRUCTIONS The safe and successful operation of the Model ZTR 6601 will depend upon the operator having the correct knowledge of all contr

OPERATION INSTRUCTIONS PARKING BRAKE SWITCH TEST: With parking brake in the OFF position, engine should not turn over or attempt to start w

OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: Cold Engine 1. Push choke control lever fully forward. 2. Push throttle control lever to 1/2 s

IMPORTANT - READ CAREFULLY The Dixon^ZTR® Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is

OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: Engine has been operated. 1. Move throttle control lever to 1/4 to 1/2 setting. 2. Insert igniti

OPERATION INSTRUCTIONS In order to achieve optimum cutting performance, please read and follow the tips listed below. Additional information can be

CARE AND MAINTENANCE This portion of the Model ZTR 6601 owners manual deals with normal service items which can be performed by the owner. Please reme

CARE AND MAINTENANCE CUTTER BLADE MAINTENANCE: NOTE: Observe proper blade position prior to removal. 1. Safely raise front of mower. 2. Hold or

CARE AND MAINTENANCE BELT TENSION ENGINE TO MOWER DECK BELT: P/N 9758 No adjustment required. Correct belt tension is maintained through a fixed engi

CARE AND MAINTENANCE FUEL SHUT OFF VALVE: A fuel shut off valve is located at the bottom rear of each fuel tank. Always turn the valve to the "OF

CARE AND MAINTENANCE REAR WHEELS: The rear wheels of the Model ZTR 6601 are of an "offset" center design to both compliment the articulation

Page 23

CARE AND MAINTENANCE LUBRICATION DRIVE SYSTEM: The gears in the HydroGear gearbox are permanently lubricated using a special grease which completely e

CARE AND MAINTENANCE HOT oil may cause burns. Allow engine to cool before draining oil. CHANGING THE ENGINE OIL: 1. The "snap lock" oil dra

CARE AND MAINTENANCE DECK LEVELING AND HEIGHT ADJUSTING PROCEDURE 1. On the right side of the machine, the tie bar between the lift arms should be a

CARE AND MAINTENANCE DRIVE SYSTEM ADJUSTMENTS: Adjustment of the drive system is limited to the actual function of the hydrostatic transmissions as ou

CARE AND MAINTENANCE PARKING BRAKE CABLE ADJUSTMENT: Position parking brake lever in the off or disengaged position. This will allow the belt idler us

CARE AND MAINTENANCE NEUTRALADJUSTMENT: Swing upper control levers out into the neutral slots. Raise upper body to the fully open position. Start eng

CARE AND MAINTENANCE FORWARD TRAVEL SPEED ADJUSTMENTS: Stop engine, move levers to drive position, lightly push each upper control lever forward until

CARE AND MAINTENANCE PROCEDURE FOR ELECTRIC CLUTCH ADJUSTMENT Electric clutches require periodic Air Gap adjustments to extend the life of the

CARE AND MAINTENANCE HYDROSTATIC TRANSMISSION OIL AND FILTER SERVICE SERVICE INTERVALS: 1. Initial oil and filter service - 50 hours. 2. Every 250

CARE AND MAINTENANCE WHEELS AND TIRES: Correct tire pressure is important for correct operation of mower. Front Tires 11X4X5 Air Pressure 16-2

STANDARD SERVICE PARTS LIST MODEL ZTR 6601: BLADES: Hi-Lift: P/N 9383 BELTS:

TROUBLESHOOTING MOWER CUT QUALITY: There are many variables that can effect the cut quality of any riding mower. Type and conditions of grass,

RIDING LAWNMOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY OR DEATH The most common causes of injury to the operator or bystander...

TROUBLESHOOTING DRIVE SYSTEM: SITUATION CAUSES REMEDY Mower pulls to one side or the other Drive adjustment Consult your dealer for repa

TROUBLESHOOTING ELECTRICAL SYSTEM: SITUATION CAUSES REMEDY Starter will not turn engine over Circuit breaker engaged Push button to reset Consu

6601 T-Box/Hydro/Gearbox

6601 Gearbox

6601 Mower Deck

6601 Chassis

6601 Fuel/Hydro Tanks & Fittings

6601 Body

Page 44 6601 Wiring

NOTES

SAFETY SYMBOLS: SAFETY ALERT SYMBOL - When you see this symbol, BE ALERT to the potential for injury. Follow recommended safety precautions and safe

DIXON INDUSTRIES, INC A BLOUNT COMPANY AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYVILLE KS 67337 O945 316 251 2OOO FAX 316 251 4117 OWNER INFORMATIO

WARNING The Engine Exhaust from this product contains chemicals known to the state of California to cause cancer, birth

SAFETY This cutting mower is capable of amputating hands and feet, and throwing objects. Failure to observe the following safety instructions could

SAFETY SLOPE OPERATION: Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe

SAFETY CHILDREN: Tragic accidents can occur if the operator is not alert to the presence of children. Children are attracted to lawn mowers and t

SAFETY SERVICE: • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. Use only an approved con