Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.RAM 48 CE / 966658601Operator Manu
SAFETY10• Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing t
SAFETY11Personal Safety Equipment• Make sure that you have first aid equipment close at hand when using the machine.• Never use the machine when bare
SAFETY128011-517Never allow children to operate the machine8011-518Keep children away from work area• Do not try to stabilize the machine by putting
SAFETY13Safe Handling of GasolineWARNING!The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s driv
SAFETY148011-515Never drive the machine in an enclosed spaceGeneral Maintenance• Never operate machine in a closed area.• Keep all nuts and bolts ti
SAFETY15Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye inj
SAFETY16IMPORTANT INFORMATIONThe parking brake is not sufficient to lock the machine in place during transport. Ensure that the machine is well fastene
CONTROLS17This operator’s manual describes the Dixon Zero Turn Rider. The rider is fitted with a Briggs & Stratton Kohler four-stroke overhead valv
CONTROLS18Steering Control LeversThe machine’s speed and direction are continuously variable using the two steering controls. The steering controls ca
CONTROLS19Throttle ControlThe throttle control regulates the engine speed and thereby the rate of rotation of the blades.In order to increase or decre
When this product is worn out and no longer used, it should be returned to the reseller or other party for recycling.©2011 All rights reserved.Orangeb
CONTROLS208058-134Choke controlChoke ControlThe choke control is used for cold starts in order to provide the engine with a richer fuel mixture.For co
CONTROLS21Tracking BoltsIf the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure is 15 psi (103 kPa
CONTROLS22Fuel TankRead the safety instructions before refueling. The machine has one fuel tank, just behind the console. The tank capacity is 3.5 gal
CONTROLS23Fuel Shut Off ValveThe fuel shut off valve is located at the left rear of the seat. The valve is off when the handle tab is turned perpendic
OPERATION24Read the Safety section and following pages, if you are unfamiliar with the machine.TrainingDue to unique steering capabilities, zero turn
OPERATION25Before Starting1. Read the sections on Safety and Controls before starting the machine.2. Perform the daily maintenance before starting (
OPERATION26Starting the Engine1. Sit on the seat.2. Raise the mower deck by pushing the release button on the top of the lifting lever. Pull the lif
OPERATION275. Move the steering controls outward to the locked (outer) neutral position.6. Move the throttle to the middle position.7. If the engin
OPERATION288. Press in and turn the ignition key to the start position.IMPORTANT INFORMATIONDo not run the starter for more than 5 seconds each time.
OPERATION298011-642Jumper cable connectionIMPORTANT INFORMATIONThe mower is equipped with a 12-volt negative grounded system. The other vehicle must a
CONTENTSINTRODUCTION ... 5General ...
OPERATION30Running1. Release the parking brake by pushing the button and moving the lever downward. NOTE: The mower is equipped with an operator pres
OPERATION31Operating on HillsRead the Safety Instructions Driving on Slopes in the Safety Instructions.• The slowest speed possible should be used be
OPERATION32Mowing Tips• Observe and flag rocks and other fixed objects to avoid collisions.• Begin with a high cutting height and reduce it until the
OPERATION33Stopping the Engine1. Move the throttle to the minimum position (tortoise symbol).2. Move the steering controls outward.3. Disengage the
OPERATION34Moving Machine By HandZT-2800 Bypass LinkagesWhen pushing or pulling the mower, engage the ZT-2800 (Integrated Zeroturn Transaxle) bypass l
MAINTENANCE35Maintenance ScheduleThe following is a list of maintenance procedures that must be performed on the machine. For those points not describ
MAINTENANCE361) First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours.2) In dusty
MAINTENANCE37BatteryYour mower is equipped with a maintenance free battery that does not need servicing. However, periodic charging of the battery wit
MAINTENANCE38Safety SystemThe machine is equipped with a safety system that prevents starting or driving under the following conditions.The engine can
MAINTENANCE39112V-beltsCheck every 100 hours of operation. Check for severe cracking and large nicks.NOTE: The belt will show some small cracks in nor
WARNING!Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these
MAINTENANCE4012Pump BeltReplacing pump beltPark the mower on a level surface. Engage the parking brake.Belt removal1. Remove the deck belt (see Deck
MAINTENANCE41321WARNING!Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.The sharpening of blades
MAINTENANCE4212WARNING!Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.IMPORTANT INFORMATIONThis
MAINTENANCE43231Caster WheelsCheck every 200 hours. Check that wheels rotate freely. If wheels do not rotate freely take the unit to your dealer for s
LUBRICATION44GeneralRemove the ignition key to prevent unintentional movements during lubrication.When lubricating with an oil can, it must be filled w
LUBRICATION45Front Wheel MountLubricate with a grease gun, one zerk for each wheel mount.Use only good quality bearing grease.Grease from well-known b
LUBRICATION46312221Transaxle Fluid ChangeThis transaxle is designed with an external filter for ease of maintenance. To ensure constant fluid quality le
TROUBLESHOOTING47Problem CauseEngine will not start • Blade switch is engaged.• Steering controls are not locked in the neutral position• Parking
TROUBLESHOOTING48Problem CauseEngine overheats • Clogged air intake or cooling fins• Engine overloaded• Poor ventilation around engine• Defective
STORAGE49Winter StorageAt the end of the mowing season (or if it will not be in use for more than 30 days), the machine should be readied for storage.
INTRODUCTION5CongratulationsThank you for purchasing a Dixon ride-on mower. This machine is built for superior efficiency to rapidly mow primarily larg
50 WIRING DIAGRAM8053-002
TECHNICAL DATA51HEX HEAD CAP SCREWSThe torque values shown should be used as a general guideline when specific torque values are not given.U.S. Standar
TECHNICAL DATA521) For engine specifications, refer to the engine manufacturer’s owner’s manual.2) The power rating of the engines indicated is the ave
TECHNICAL DATA53Ram 48ZT 966658601FrameCutting Width 48" / 122cmCutting Height 1½ - 4½" / 3.8 - 11.4 cmUncut Circle 0Number of Blades 3Blade
54CONFORMITY CERTIFICATESConformity Certificates For Model Listed Below:966658601 / RAM 48 CE Zero Turn RiderUSA requirementsLabels are placed on the e
55SERVICE JOURNALActionDate, mtr reading, stamp, signDelivery ServiceCharge battery rAdjust tire pressure of all wheels according to Technical Data
56SERVICE JOURNALActionDate, mtr reading, stamp, signAfter the First 10 HoursChange engine oil r25-Hour ServiceCheck the fuel pump’s air filter rChec
57SERVICE JOURNALActionDate, mtr reading, stamp, sign50-Hour ServicePerform the 25-hour service rClean/replace the air cleaner’s filter cartridge (pap
58SERVICE JOURNALActionDate, mtr reading, stamp, sign300-Hour ServicePerform the 25-hour service rPerform the 50-hour service rPerform the 100-hour
INTRODUCTION6Good ServiceDixon’s products are sold only in specialized retail stores with complete service. This ensures that you as a customer receiv
SYMBOLS AND DECALS7R NThese symbols are found on the machine and in the operator’s manual.Study them carefully so that you know what they mean.IMPORTA
SYMBOLS AND DECALS8Moving sharp blades under coverRead Operator’s ManualShut off engine and remove key before performing any maintenance or repair wor
SAFETY9Safety InstructionsThese instructions are for your safety. Read them carefully.General Operation• Read, understand, and follow all instruction
Kommentare zu diesen Handbüchern